Allied Vision Technologies Pike Manual de instrucciones Pagina 194
- Pagina / 332
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Controlling image capture
PIKE Technical Manual V4.0.0
194
Which new sequence mode features are
available?
New features:
• Repeat one step of a sequence n times where n can be set by the vari-
able ImageRepeat in SEQUENCE_PARAM.
• Define one or two hardware inputs in Input mode field of IO_INP_CTRL
as:
– Sequence step input (if two are set as input, they are AND gated) or
– Sequence reset input
Setup mode
The SetupMode flag allows you to set up a sequence while capturing images.
Using this flag you get a visual feedback of the settings. Set this flag when
setting up the sequence and reset the flag before using the sequence.
I/O controlled sequence stepping mode
The I/O controlled sequence stepping mode can be done level controlled
or edge controlled:
The I/O controlled sequence stepping mode can be set for ervery single
sequence entry. Thus a sequence can be controlled in a very flexible manner.
Note
L
From now on:
sequence step is I/O controlled sequence stepping mode
sequence reset is I/O controlled sequence pointer reset
Level controlled Edge controlled
• As long as the input is in high
state the sequence pointer will
be incremented from image to
image.
• Can be combined with Quick
Format Change Modes. See
Chapter Standard Parameter
Update Timing on page 152 and
Chapter New: Quick Format
Change Mode (QFCM) on page
152.
• Level change is asynchronous to
image change.
• A rising edge on the input will
cause one pointer increment
immediately.
• Can be combined with Quick
Format Change Modes. See
Chapter Standard Parameter
Update Timing on page 152 and
Chapter New: Quick Format
Change Mode (QFCM) on page
152.
Table 81: Description of sequence stepping control
- Technical Manual 1
- AVT Pike 1
- Legal notice 2
- Contents 3
- Introduction 10
- Before operation 13
- Declarations of conformity 14
- *: also -15fps variant 15
- Safety instructions 16
- Cautions 17
- Environmental conditions 17
- PIKE types and highlights 18
- FireWire 21
- FireWire in detail 22
- 1394b bandwidths 27
- FireWire hot plug precautions 31
- Operating system support 31
- System components 32
- Camera lenses 34
- Specifications 36
- PIKE F-032B / F-032B fiber 37
- PIKE F-032C / F-032C fiber 39
- PIKE F-100B / F-100B fiber 41
- PIKE F-100C / F-100C fiber 43
- PIKE F-210B / F210B fiber 49
- PIKE F-210C / F-210C fiber 51
- PIKE F-421B / F-421B fiber 53
- PIKE F-421C / F-421 C fiber 55
- PIKE F-505B / F-505B fiber 57
- PIKE F-505C / F-505C fiber 59
- Spectral sensitivity 61
- Camera dimensions 67
- Tripod adapter 69
- Pike W90 (2 x 1394b copper) 70
- Pike W270 (2 x 1394b copper) 74
- Adjustment of C-Mount 81
- F-Mount, K-Mount, M39-Mount 82
- PIKE fiber 84
- Status LEDs 90
- Operating the camera 92
- In1 – Pin 4 94
- In2 – Pin 11 94
- InGND – Pin 7 94
- PIKE Technical Manual V4.0.0 100
- Camera interfaces 102
- Pixel data 107
- Description of the data path 110
- Color cameras 111
- Channel balance 112
- White balance 115
- Automatic white balance 118
- Auto shutter 119
- Auto gain 121
- Manual gain 123
- Horizontal mirror function 125
- Shading correction 126
- How to store shading image 127
- Output = f (Input) 133
- Write n databytes 134
- 2 x / 4 x / 8 x binning 135
- Vertical binning 136
- Horizontal binning 138
- Figure 75: 8 x full binning 141
- 8 x full binning 141
- What is sub-sampling? 142
- Description of sub-sampling 142
- 2 out of 16 H+V sub-sampling 146
- Why new timing modes? 151
- ☺ Disadvantage 153
- Packed 12-Bit Mode 156
- Deferred image transport 157
- HoldImg mode 159
- FastCapture mode 161
- (BAYER demosaicing) 162
- Sharpness 163
- Hue and saturation 164
- Color correction 165
- Color conversion (RGB YUV) 167
- Bulk Trigger 167
- Level Trigger 167
- Serial interface 168
- Controlling image capture 173
- Trigger delay 178
- Exposure time 180
- Minimum exposure time 181
- Extended shutter 181
- One-shot 183
- Exposure 185
- Multi-shot 186
- ISO_Enable / Free-Run 186
- Asynchronous broadcast 186
- Jitter at start of exposure 187
- Sequence mode 189
- SetupMode to 193
- Disable SetupMode 193
- SIS: Definition 198
- SIS: Scenarios 198
- Smear reduction 200
- PIKE F-032B / PIKE F-032C 201
- PIKE F-100B / PIKE F-100C 203
- PIKE F-210B / PIKE F-210C 207
- PIKE F-421B / PIKE F-421C 209
- PIKE F-505B / PIKE F-505C 211
- Area of interest (AOI) 213
- Autofunction AOI 215
- Frame rates 216
- Frame rates Format_7 220
- PIKE F-032: AOI frame rates 221
- PIKE F-100: AOI frame rates 223
- (no sub-sampl.) 229
- (sub-sampl.) 231
- AOI height / pixel 232
- Frame rate / fps 232
- PIKE F-421: AOI frame rates 236
- PIKE F-505: AOI frame rates 238
- Test images 243
- Test images for color cameras 244
- Configuration of the camera 245
- Sample program 249
- Example FireStack API 250
- Configuration ROM 251
- Implemented registers 254
- Format_7 276
- Advanced features 278
- Advanced feature inquiry 283
- Camera status 285
- Maximum resolution 286
- Time base 286
- Look-up tables (LUT) 290
- Frame information 297
- Input/output pin control 297
- Delayed Integration enable 298
- Auto shutter control 299
- Auto gain control 300
- Mirror image 304
- Soft Reset 305
- Parameter-List Update 309
- Format_7 mode mapping 310
- Secure image signature (SIS) 312
- User profiles 317
- GPDATA_BUFFER 320
- Firmware update 321
- Appendix 322
- PIKE Technical Manual V4.0.0 332
- , 117, 118 332
Relacionado con productos y manuales para Cámaras Bridge Allied Vision Technologies Pike
(49 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.038 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales